Call: 336 752 2879
Fax: 336-752-2869
Back To Index - Contact Info - Secure Ordering

Drivetrain And Rear Axle Components,
Brakes, Steering And Suspension

axel yoke kit
complete driveshaft pinion yoke kit includes yoke,u-joint retaining straps,strap holddown bolts,yoke retaining washer and nut and instructions.
P4529481AC Axle Yoke Kit — 29 Spline, 7260 Joint
(8-1/4" and 8-3/4" Axles)		 96.95
P4529483AB Axle Yoke Kit — 29 Spline, 7290 Joint
(8-3/4" Axles)		 80.50
P4876804AB Axle Yoke Kit — 10 Spline, 7290 Joint
(Dana 60 Axles, 8-3/4" Axles)		 170.95

Billet Yoke Kits

For use with 742 or 489 housing or Mopar Performance aluminum housing (4876445). Kits include u-bolts and pinion nut.
P45106388 3/4" 10 spline Axle Yoke--1.078" bearing cap, aluminum billet 205.95
P45106558 3/4" 10 spline Axle Yoke--1.125" bearing cap, aluminum billet 205.95
P45106568 3/4" 10 spline Axle Yoke--1.078" bearing cap, 4130 chromoly billet 170.95
P45106578 3/4" 10 spline Axle Yoke--1.125" bearing cap, 4130 chromoly billet170.95

Slip Yoke Kits

For use with driveshaft kits or general service.
P5007409 A-904 with type 7260 u-joint-26 spline-6.8" long. 31.95
P5007410 A-904 with Type 7290 U-Joint-26 Spline-7.30" Long. 37.95
P5007411 A-727 with type 7290 u-joint-29 spline-8.0" long. 68.95
universal joint package
u-joint for driveshaft use.
P3690773 1330 series-u-joint assembly 26.95
P5007418 u-joint adapts 7260 driveshaft to 7290 axel yoke. 36.95
u-bolt yoke conversion-29 spline
converts standard strap type assembly to stronger u-bolt assembly on dana 60 axels w/type 7290 u-joints. Allows use of stock prop shaft.
P4120714AB u-bolt yoke conversion dana 60. 179.95
P5007417AD yoke kit. Adapts 7290 yoke to 7260 drive- shaft-29 spline-8 3/4" carrier. 104.95
u-joint u-bolt assembly package
P3690774 service parts for u-bolt assembly, two required (use with p3690771 yoke) 3.95
u-joint strap and bolt packages
P4120468 type 7260 (small u-joint) 3.95
P4120469 type 7290 ( large u- joint) 3.95

Rear Axle Components

ring and pinion gears
these high performance rear end ring and pinion gear sets are manufactured with a special heat treat process.they are made with special needs of drag race and off-road in mind. Available in wide range of ratios.
9 1/4" rear axel (12 bolt cover)
P4529272AB 3.90:1 ratio 197.95
P5249927 3.55:1 ratio 215.50
Differential housing
aluminum 8 3/4" carrier housing this rugged aluminum center section is designed to hold up under high torque and save weight at the same time.uses 1 3/4 large stem pinion and standard components the 8 3/4"aluminum axel housing: uses "742" style large stem ring and pinions fits 8 3/4" banjo housings(up to '74) weight reduction of 44%-approximatly 11LBS to 14LBS(compared to production cast iron) features 6061 billet aluminum caps,stiffer than cast iron housing, decreases pinion deflection 10%. Uses "742" style bearings and shims,service parts and sure-grips, like p4876118. clearance required on 3.23 or higher ratios.
P4876445 bare housing-aluminum 977.95
P5007239 gasket-8 3/4" housing 7.95

Axle Brace

Keeps axle tubes from twisting under extreme loads, and provides strength and rigidity to Chrysler 8-3/4" axles. Welding required.
P4510642 Axle Brace (8-3/4" Axles) 79.95
Differential clutch kit
original equipment clutch disc and plate to rebuild a limited slip differential. Includes instruction sheet.
P4529484 ALL-8 3/4" 59.00
P4529485 ALL- 9 3/4" 65.50
rear axle bearing set
specifically designed by mopar performance parts to eliminate the production bearing retainers and axle end play adjuster. each set contains 2 axle shaft bearings, 2 bearing retainer sleeves,2 axle shaft seals and 2 axle flange gaskets. Fits 1965 and newer axles.
P5249444 8 3/4" & 9 3/4" axles 103.95
crush sleeve
original equipment crush sleeve for setting up rear axel. Includes pinion nut washer and pinion flange nut.
P4529700 ALL-8 1/4" axel 6.50
P4529702 ALL-9 1/4" axel 6.50
ring gear bolt package
complete set of 12 ring gear retaining bolts with instructions.
P4529486 right hand thread,1971& newer-7 1/4" 1972 & newer-8 1/4",1971 & newer 8 3/4" 6.95
P5249163 left hand thread, 1970 & older 7 1/4" , 1971 & older 8 1/4", and 1970 & older 8 3/4" 51.00
sure grip differential assembly
mopar performance parts supplies production replacement sure-grip differential assemblies for rear axels. these assemblies are complete, including instruction sheet for high performance applications. Designed for gear ratios of 2.76:1 and numerically higher.
P4529273 all 8 1/4" thru 1995 312.00
P4876118 all 8 3/4" 713.00
RWD chrome differential cover
attaching bolts not included.
P3690753 8 1/4" axle 49.95
P3690754 9 1/4" axle,1973 and newer 49.95
P3690755 dana 60 9 3/4" axle 47.50
chrome attaching bolts
package for chrome rear axle covers.
P4452787 set of 12-7 1/4", 8 1/4", and 9 1/4" 18.95
P5249719 set of 9- 9 3/4" 18.95
rear axle shim package
mopar performance parts has developed these tapered pinion angle shims so the pinion-to-driveshaft angle can be adjusted to the correct 5-7degrees. Kit includes 2 each 1 degree,2degree,3degree shims. (6 total shims).
P4529536 rear axle shim pkg. 81.50
P5153561 Rear Axle Shim — 1°, 2pcs. 26.50
P5153562 Rear Axle Shim — 2°, 2pcs. 28.50
P5153563 Rear Axle Shim — 3°, 2pcs. 31.50

Brakes

Stainless Master Cylinder Heat Shield

Prevents heat from exhaust header or exhaust manifolds from boiling and degrading brake fluid--perfect for big block, A-body conversions.
P4510634Stainless master Cylinder Heat Shield29.95
master cylinder adapters
for use with mopar performance parts master cylinder assemblies p5249270 and P5249271. contains adapter,2 retaining nuts, to be used with brake cylinder pushrod pkg. p5249316. converts 4 stud to 2 stud attaching style.
P5249315 master cylinder adapter. 33.50

Offset Master Cylinder Adapter

Moves the master cylinder away from the engine for added clearance with Hemi or 440 engine valve covers. Designed specifically for 1968 Hemi A-Body cars. Can also be used for other A-body applications when installed on 426 Hemi engines. For use with P5249270 and P5249271 lightweight master cylinders.
P5249717Offset Master Cylinder Adapter (Hemi A-Body) 97.95

Adjustable Brake Pushrod

For use with P5249270 and P5249271 lightweight master cylinders.
P4510640Adjustable Brake Pushrod52.00
brake cylinder pushrod package
for use with mopar performance parts master cylinder assemblies p5249270 and p5249271 and master cylinder adapter p5249315.package contains pushrod assy. bolt, nut, washer,adhesive, roll pin and instructions. Some assembly required.
P5249316AB brake cylinder pushrod package 65.00
brake proportioning valve
lightweight brake proportioning valve lightweight unit is fully adjustable if you have a split brake system front to rear. the proportioning unit is made from lightweight billet aluminum and is compact for all applications and is easily adjusted with the turn knob.
P5249088 lightweight brake proportioning valve 65.50

Steering And Suspension

XHD Leaf Springs — Original Equipment

These extra heavy-duty O.E. leaf springs are just like the bias design production springs that were stock on 1968–72 A-Body vehicles with 340 high-performance engines, 1967–71 B-Body vehicles with 440 or 426 manual and automatic transmissions, and 1970–74 E-Body vehicles with 440 or 426 manual or automatic transmissions. Springs will fi t any A-Body (1968–72), B-Body (1966–72) or E-Body (1970–74), regardless of engine size, and come with front bushing installed in assembly. B-Body: front 22", rear 36". Select right or left spring. Lighter cars may sit higher than stock.
P4510268 O.E. Leaf Spring — Right (1964–75 A-Body) 152.95
P4510269 O.E. Leaf Spring — Left (1964–75 A-Body)152.95
P4452982 O.E. Leaf Spring — Right (1966–72 B-Body) 99.50
P4452983 O.E. Leaf Spring — Left (1966–72 B-Body) 99.50
P4452984 O.E. Leaf Spring — Right (1970–74 E-Body) 92.50
P4452985 O.E. Leaf Spring — Left (1970–74 E-Body) 92.50

Competition Leaf Springs — Super Stock

Designed to control torque roll, providing equal bite on rear wheels through limited axle windup. These springs don’t lock up the rear, but allow it to move, keeping the tires on the track where they belong. The rear springs listed below have a 20" front segment and require a longer front spring hanger bracket for B-, E-, F-, J- and M-Bodies (not included). Standard hanger brackets used on A-Body. With P3412002–03, the rear eye in frame is moved forward; Pinion Snubber is recommended. If using P4120863, vehicle will not be level at standstill.
P4120863 right-2800lb car weight-pro gas 93.50
P4120864 left-super gas bracket car 93.50
P3412002 right -original 1968 hemi ss 106.50
P3412003 left- use on modified cars and all race hemi ss. Requires rear shackle relocation on B body cars. 106.50
P3690456 right- 3400lb car weight 104.95
P3690457 left-including 1964-65 ss B- body 106.50
P3690454 right-3800lb car weight 106.50
P3690455 left- B- body 106.50
P4120865 right-3300lb 93.50
P4120866 left-E-body(barracuda-challenger) requires rear shackle relocation on B-body. 93.50
P3690460 right-3600lb 106.95
P3690461 left- E-body(barracuda-challenger) requires rear shackle relocation on B-body . 106.95

oval track leaf springs
re-issued mopar performance parts kit car leaf springs are ideal for oval track applications these springs are widely used on dirt track race cars. The spring rate is 120 LBS per inch.front20.5" rear 35".
P4529414 zero arch 82.00

Solid Leaf Spring front Eye Bushings

Contains (2) 1.5" aluminum spring eye bushings with steel sleeves. Improves spring reaction by cutting down on rubber deflection. Steel sleeve allows free movement of aluminum bushing.
P4510644Aluminum 1 1/2" diameter, 2" length70.00
Rear Shackle Bushings Sets of 8.
P4510643 A-body, high-performance polyurethane 22.50
rear spring shackle bushings
original equipment rear spring shackle bushings are heavy duty rubber for A,B, or E body vehicles. These bushings are factory original equipment for restoration projects.( sets of 8 bushings).
P4452986 A-body (7/8") 42.50
P4452987 B&E body (1") and super stock springs. 10.95
rear spring clamp package
increases stiffness.(2 per package)
P4120470 rear spring clamp pkg.-2 1/2" springs only 38.50
rear spring front hanger bracket sets
2" longer straight type hangers for use with super stock springs.
P4120079 Front Hanger Bracket Set — 117" Wheelbase (1966–70 Dodge B-Body Sedan and Wagon) 69.95
P4120105 Front Hanger Bracket Set — 116" Wheelbase (1966–70 Plymouth B-Body Sedans, 1971–74 B-Body Wagons) 69.95
P4120080 Front Hanger Bracket Set — 108"/110"/115" Wheelbase (1964–65 Mod. B-Body, 1970–74 E-Body, 1971–74 B-Body HT) 58.95
P4120081 Front Hanger Bracket Set — 110" Wheelbase (1976–80 F-Body, 1980–83 J-Body, 1977–78 MBody) 71.00
rear spring front hanger bracket set offset.
moves springs in next to frame.requires spring seats to be moved, also offset shackles
P4120077 A- body 115.00
P4120078 E-body w/super stock springs. 64.00
rear spring mounting seats
these seats work with all 3" diameter tube rear axles.(8 1/4,8 3/4, 9 1/4, 9 3/4")
P4120074 Rear Spring Mounting Seats 8.00
P5007857Rear Spring Mounting Seats — for Super Stock Springs 25.95
rear spring shock mounting plates
these plates are designed for RWD,A,B, and E body cars.provides lower shock pivot plus support for the u-bolts that hold rear spring to axle.
P4876518 right-A,B,& E-bodies 55.50
P4876519 left-A,B, &E-bodies 55.50
spring relocation kit
moves springs in 3" per side for added tire clearance.mounts longitudinally.requires welding. Includes front hangers,shackles, rear shackle mounts,and spring mounting seats.
P4120665AB B&E bodies 132.50
P4876558AB A- body 185.50
spring u-bolt & nut package
package includes 4 spring/axle u-bolts and 8 nuts.
P5249709 includes(4) 7" u-bolts & (8) nuts. 47.50
P4120611 includes (4) 8" u-bolts & (8) nuts. 43.95
P4120612 includes (4) 9" u-bolts & (8) nuts. 34.95
straight shackle set
package comes with bushings,side plates, and nuts.
P5249715 A-body-1 shackle only 49.95
P5249716 B-body-1 shackle only 35.95
rear shackles
offset shackle sets: offset is approximately .80" for use on super stock cars with relocated rear springs. Use with offset front hangers.
P4120075 A-bodies 81.00
P4120076 B&E bodies 63.95
bolt-in frame connector packages
this package lets you tie the front and rear frame longitudinally on all A or B bodied drag cars.package includes 2 connectors, brackets and necessary mounting hardware.
P4286868 A-body 1967-76(108" wheelbase only) 135.00
P4876658 A-body 1967-76(111" wheelbase only) 129.95
P4286869 B-body 1966-mid 1972 135.00
P4286870 E-body 135.00
adjustable pinion snubber
unit fits to front of the rear axle housing. it helps control axle wind-up by adjusting the height to the floor pan,depending on individual requirement.
P3690182 ALL 8 3/4" axle 55.95
P3690181 ALL 9 3/4" axle 55.95
Torsion bars
mopar performance torsion bars for the A,B,and E body cars in a variety of diameters for restorations,performance, and racing. Improve the suspension performance and increase cornering ability or weight transfer of your vehicle with these mopar performance parts torsion bar sets.these A-body bars are 35.7" long.the B and E body bars are 41" long. These bars bolt right in to stock locations w/out modifications. (sold as sets)
A body torsion bar sets
P5249148 .810" diameter-drag race applications 312.00
P5249150 .890" diameter resto, for 383 cars, improved "A" engine handling312.00
P5249151 .920" diameter- performance handling,solo racing. 312.00
B and E- body torsion bar sets
P5249157 .920" diameter- resto, for 440 and hemi cars improved "A" engine handling 188.00
P5249158 .960" diameter-improved"B/RB" and hemi handling. 188.00
torsion bar lock/seal set
set of two snap rings and seals for use
when changing torsion bars.
P5249609 A,B, and E bodies 49.00
P4876097 clips only ( to service p5249609) 6.95
front end seal package
this package contains seal for tie rod ends, pitman arm, upper and lower, ball joints,and idler arm.
P5249226 1968-76 A&E body 216.00
RWD front strut bushing package
used to minimize fore and aft movement during braking and hard acceleration.
P4529183 1967-76 A-bodies 7.95
P4529184 ALL B&E bodies 14.95
steering racks and gears
manual steering gear worm and ball nut package replace your 26:1 manual steering production gear ratio set with this improved 20:1 ratio
P4007612 manual gear box-1963 to 1985 passenger car. 242.00
Power Steering to Manual Steering Adapter Allows you to convert vehicles equipped with power steering to a manual steering box.
P4510637Manual Steering Adapter162.95
Drag racing rear shock asborbers
these rear shock absorbers are designed with the extended length required by special drag racing applications. sold individually.
P4529514 A- body with automatic transmission 36.50
P4529515 B&E bodies with automatic transmission 36.50
P4529516 A- body with manual transmission 36.50
heavy-duty suspension bushings
these bushings are recommended for circle track, solo and road racing applications they can also be used in drag racing where they apply. passanger car
P4876196 control arm bushing kit-front-1962-76 A body 55.95
P4876197 rear leaf spring bushing kit- standard- front eye. 55.95
P4876206 transmission mounts-1967-83 A,B,C,E,F,& M-bodies. 22.50
P5007087 bushing kit-leaf spring set-rear 1965-72 B-body except 426 and 440 models. 56.95
P5007088 bushing kit-leaf spring set -rear 1965-72 B-body 426 and 440 models. 56.95
replacement end link bushings
these bushings can be used to replace your stock bushings or on the mmp sway bars. extra hard for positive stiffness and longer wearability. 8 included per set
P4349116 end link bushings 21.50
RWD rear wheel stud sets
studs for RWD cars are heavy duty and extra long to allow use of wheel spacers.
P4120610 1/2" diameter disc brakes,10 studs per set 15.95
P4120625 1/2" diameter drum brakes,10 studs per set 38.95
FWD wheel stud set
special FWD wheel studs have increased length for custom and racing wheel applications.a direct replacement for production.
P4349052 FWD 12x1.5mm diameter-ALL L&G bodies front and rear brakes,(4) studs per set 4.95

S/S TIE ROD SLEEVES

Set of two Polished Stainless Tie Rod Sleeves that are far superior to the stock OEM style split sleeves. These provide more positive steering and eliminate flex during acceleration or braking for better control. The are made from Solid Stainless Steel Hex Bar and are threaded for right-hand and left-hand. Two sleeves and four jam nuts.
TR-300168-77 A Body Mopar$64.00
TR-3001H68-77 A Body Mopar - Heavy Duty 11/16 $84.00
TR-300262-70 B Body Mopar $64.00
TR-3002H62-70 B Body Mopar - Heavy Duty 11/16 $84.00
TR-300371-74 E Body Mopar $64.00
TR-3003H71-74 E Body Mopar - Heavy Duty 11/16 $84.00

SSrod
STRUT ROD
17-4 STAINLESS STEEL HEX ROD
3-7001MOPAR A BODY $185.00pr
3-7002MOPAR B & E BODY $185.00pr

SSwasher
Polished Stainless Washers
3-4620 B BODY & E BODY Rear Shock Absorber Washers
4 per set - Polished Stainless U.S.A. MADE BY MMS		$15.00
3-4621 MOPAR E BODY STRUT ROD WASHERS
4 per set - Polished Stainless U.S.A. MADE BY MMS		$25.00
3-4622 MOPAR B BODY STRUT ROD WASHERS
4 per set - Polished Stainless U.S.A. MADE BY MMS		$25.00
3-4623 MOPAR A BODY STRUT ROD WASHERS
4 per set - Polished Stainless U.S.A. MADE BY MMS		$25.00
3-4624 MOPAR E BODY UPPER SHOCK WASHER
2 per set - Polished Stainless U.S.A. MADE BY MMS		$8.00
3-4625 MOPAR B BODY UPPER SHOCK WASHER
2 per set - Polished Stainless U.S.A. MADE BY MMS		$8.00

Last Updated on 11/09

more parts available - call for prices

| Back to Index | Order Complete Catalog |Back to top | Secure Order Form |